We may earn revenue from the mathematical product usable on this page and participate in affiliate broadcast . memorize More ›
If “ supplant kitchen faucet ” is on your to - do listing , you ’ll be beaming to know that change or instal a new spigot is a reasonably simple home melioration undertaking . The downside is that it usually requires contorting your trunk into a pretzel - like shape under the sink .
Barring any troubles you have getting inside the locker and out again , installing a new kitchen faucet should take less than an hour .
istockphoto.com
Project Overview
Working Time:45 minutesTotal Time:45 minutesSkill Level : EasyEstimated Cost:$160
Before You Begin
Before you put in akitchen faucet , take a look at the sink . All sinks have some the same introductory office :
Most faucets are attached to the cesspool by a plastic nut ( on old faucets , the nut might be metallic element ) . There are some faucets that mount with bolts on the top of the cesspool , but it ’s more than likely you will necessitate to wedge yourself inside the console under thesinkto accomplish this facility .
Toremove an honest-to-goodness faucet , exclude the water off at the valve under the sink or at the main shutoff valve to the firm . Then , come away the hot and stale water supply lines and the nuts guarantee the spigot to the sink .
istockphoto.com
Tools & Materials
Bobvila.com may clear a military commission from purchases made through these links .
STEP 1: Install the gasket.
Most new faucet come with a rubber or credit card gasket that keeps the roast between the swallow hole and the spigot from leak . Before put in a newkitchen spigot , first put the faucet ’s gasket in space . Push the gasket in around the substructure of the spigot ( or under the scutcheon denture that cover the sump ’s loose holes , if you ’re install a one - hole spigot in a three- or four - trap sinkhole ) .
If your new faucet did not fall with a gasket , roll out a thin “ snake ” ofplumber ’s puttyand match it around the base of the spigot where it will meet the sink .
STEP 2: Set the faucet in the hole.
After the gasket or putty is in place , prey the whippy supplying line or PEX piping through the hole in the sink , and localize in the faucet . ( If you ’ve used plumber ’s putty , you may clear away any nimiety with aputty knifeor utilize a finger . )
Crawl under the sink and tighten the plastic nut until it almost hits the undersurface of the cesspit . fasten each of the mounting nookie until the faucet is tight against the sinkhole . engage a helper to verify the faucet is straight and decent pose in the hole or escutcheon before making any concluding adjustments .
STEP 3: Connect the faucet to the water lines.
Some new faucets , include Delta faucets , amount with flexible PEX personal credit line that are already connected to the spigot , which make this step very well-heeled . In this case the hose just need to be connected at the water valve . Take care to connect the hot and frigid PEX supply personal credit line to the appropriate water valve .
For faucets that do not havePEX pipingattached , you ’ll need to runflexible pipingsupply line from the spigot to your water provision valve . Take care with this measure — you do n’t want to damage the pipe that run into the wall by jostling it too much .
enclose a strip ofTeflon plumber ’s tapearound the pipe ’s ribbon to give the connection a tight cachet .
istockphoto.com
Give the nut on the flexible pipage a few manual turns before using a twist to attach them firmly to the body of water provision valve . you could use an adjustable twist for the problem , but if your water lines are behind the sink basin near the top of the cabinet , abasin wrenchwill make this job a lot easier .
STEP 4: Check for leaks.
After associate the spigot to your pee supply , bend on the spigot and check for anyfaucet leaks . bear exceptional aid to the gasket where the cesspit meets the spigot and also to the supplying line and valve connectedness under the sink . Tighten nuts and gasket as needed , but take forethought not to overtighten them .
STEP 5: Remove the aerator and flush out the faucet.
kick in how much tugging and bump was just done on these pipes and valves , there ’s a good chance that you ’ve dislodge some rubble and mineral deposit inside the water lines . To flush it out , remove thefaucet aerator(that small screen on the end of your spigot that keeps these deposits from terminate up in your shabu of water ) . Some spigot model come with a tool with which you could move out the aerator ; on other spigot , the aerator can just be unscrewed .
Turn the faucet on all the way and let the water hightail it for a minute of arc or two . rinse off and supplant the aerator .
Final Thoughts
Replacing a spigot is a fairly easy DIY project that usually takes less than an hr to complete . To make the job go swimmingly , make trusted that your newfangled faucet apparatus has the same number of holes as your sinkhole , and check to see that all the supplies that are n’t let in with the new faucet are on hand when beginning the facility .
FAQs
While instal a new kitchen faucet is a pretty straightforward job , there are real - life variables that can perplex the process . To help oneself make this project comfortable , we ’ve resolve some of the most common questions about how to set up a faucet .
Q. How much does it cost to replace a faucet?
The cost of replacing a faucet depends largely on how much you spend on the novel spigot and whether you ’re set up it yourself . If you are replacing a faucet with an inexpensive model , the projection can be as small as $ 100 . If you ’re hiring a plumber to interchange a faucet , it can costan average of $ 260 or more .
Q. How do you use plumber’s putty?
The eubstance of plumber ’s putty is interchangeable to that of Play - Doh . You ’ll first want to warm the putty in your hands until it is soft . Then extend and roll the putty into a long , Snake River - like tube . eventually , press it into blank space .
Q. How long should a sink faucet last?
The length of service of a faucet depends on many factors , include its pattern , material , and the type of water take to the woods through it . Hard H2O is toughened on all plumbing , including spigot . In cosmopolitan , however , a spigot can be require to last 15 years or more .
Q. Can you put a one-hole faucet in a three-hole sink?
Yes , you could supplant a three - hole faucet with a one - hole spigot . To handle the superfluous jam , apply a deck plate , which is also cry an escutcheon plate .
Q. How does a single-hole faucet work?
individual - hole spigot have lines for both hot and cold water combine in the faucet . When the spigot is turned on , there is an interior valve that releases the required amount of red-hot or cold-blooded water .
This Is the class for a Kitchen Renovation
Whether you ’re sell or staying , everyone can get something out of a kitchen update . Learn why we study this redevelopment the Most Valuable Project of 2025 and how to stay on budget .
depositphotos.com
Kit Stansley
istockphoto.com
istockphoto.com
istockphoto.com
